Procurement of acv auxiliary ard-2020 spares, nut nyloc m10a2, sikaflex white 300ml, rivet 4.8 x 18 mm, rivet pop 4.8 x 23.5 mm, sikaflex 221 (black), strut forward straight, strut standard, strut stn 2800 inboard, strut stn 18190 inboard, strut aft angled, strut vertical, strut aft angled, layshaft flange(drwg 80-3-3), propeller driver pulley (drwg 80-3-04 no. 17), propeller layshaft bearing sleeve nut and tab washer, lay shaft c/w with two keys, taperlock bush 2517x60, 8mm large mouth rapid link, drive belt, pintle assy, 1570 mm hose assembly 1. fittings @ 90 degree, 1600 mm hose assembly 2. fittings @ 90 degree, 6800 mm propeller pitch hose assembly 5, 7170 mm propeller pitch hose assembly 7. fittings @, 8510 mm propeller pitch hose assembly 8, 6850 mm propeller pitch hose assembly 9, 4630 mm steering hose assembly 4, 1420 mm steering hose assembly 9. fittings @ 270 degree, 6210 mm steering hose assembly 10. fittings @ 270 degree, 3530 mm steering hose assembly 11, pulley - 50 tooth lift fan driver, transmission pulley - propeller driven, universal joint repair kit, centaflex adopter plate, 2830 mm skirt hose assembly 1. bulkhead - ram. port(h0021804), 3010 mm skirt hose assembly 2. bulkhead - ram,port (h0021805), 4130 mm skirt shift assembly 4. bulkhead ram.stbd (h0021807), propeller drive belt, 1520 mm hose assembly 3. fittings @ 110 degree, 4710 mm steering hose assembly 5. fittings @ 180 degree, pulley lift fan driven 60 tooth 14mm pitch, 4020mm skirt shift hose assy 3 bulkhead - ram, bearing locating ring 55mm(spacer), st/st rod end rh male m16 gar hw16rr, st/st rod end lh male m16 gar hw12rr, pressure gauge 1/4" bsp 63mm 0.40 bar bottom entry, propellet pitch change link, skirt loop material (pennel orca 258619), skirt outer loop with ap diaphragm 8000td 80-6-10 ghl, rear inner loop, outer loop, metal oval hatch, bridge plate 316m6x30ws-60x30pl, 16 mm mailon rapidlink large mouth, bearing-taper roller(32020x), rod end m 12 (sme 45.12), bearing- taper roller, 22313ek skf bearing, eriks tpe r seal (85x120x12) 316 st/st, eriks type r seal (120x160x12) 316 st/st, seal kit double lip tsna 313, centaflux coupling (cf-a-90-g-1-1-60-l=240, fwd lift fan bearing, aft lift fan bearing, taperlock bush aft lift fan (55mm dia) 3525-55, bearing (stub axle aft) 6310, bearing (stub axle fwd) 6212, key 14x100, key 14x70, key 14x150, mobile grease xhp 400 g cartridge (notemoq box of 12) use hydr-0347, lift fan shaft seal forward, water temp. gauge, module low hyd oil, circuit breaker 62a 2pole, fuse gsa 125a, battery radio 12v 25 ahq dry fit type maintenance free, sensor 600mm w ballast, sender/ switch pressure 360-081-030-009, smoke detector optical+remote, battery charger 24v 50 amp, oil tamperature gauge- a2c59514160, condensor cooling fan, main supply isol;ator 24 dc coil blue seas 7703100b, rediator flap actuator servo motor (24 v), loud hailer horn pa-60/40, strip led, joy stick steering, rod end m8, rod end m8 lh, drive belt apu, pyrogen mag-4, oil pressure gauge 0-10 bar (0-145 psi), voltmeter 24v n02410911, steering pump p11a-193pa/107-as14-96, stop solenoid-12v, radar display tracker ball, inner loop, m6 penny washer, pyrogen mag 5, 9060 mm steering hose assembly 1. fittings @ 270 degree, 3660 mm steering hose assembly 3. fittings @ 310 degree, 1265 mm steering hose assembly, 1270 mm steering hose assembly 12, washer pain m16 st/st form a, axilock-s(type iv nbr dia-50.5 mm ), 8mm key pin shackle, bilge pump manual, em2 control pcb, line mounted relief valve-rv10 26c3b n 15, bush delrin rudder/ elevator (80-4-2 rev2/13), rudder bush, kit overhaul gasket, feedback unit (rudder system), water temp sensor switch, fuel injector, cold skirt curing agent (make-alpha), cold skirt bonding agent (make- alpha), skirt shift restrain chain, round inspection hatch, fuel sensor, hydrojet lp system valve, radiator flap temp switch(port)fw murphy tulsa usa, vibration sensor monitron, seal lay shaft plummer block fwd/aft.
Procurement of acv auxiliary ard-2020 spares, nut nyloc m10a2, sikaflex white 300ml, rivet 4.8 x 18 mm, rivet pop 4.8 x 23.5 mm, sikaflex 221 (black), strut forward straight, strut standard, strut stn 2800 inboard, strut stn 18190 inboard, strut aft angled, strut vertical, strut aft angled,
Ballast Tenders, Battery and Cell Tenders, Bearing Tenders, Bolts And Nuts Tenders, Circuit Breakers/Fuse Tenders, Condenser Tenders, Conveyor Tenders, Coupling Device Tenders, Fan and Blower Tenders, Hose Tenders, M S Plate Tenders, Pulley Tenders, Radiator Tenders, Rivet Tenders, Rod Tenders, Security Equipment Tenders, Sleeve Tenders, Structure Materials Tenders, Switches/Plug Tenders, Valve Tenders, Washer Tenders, Wire And Cable Tenders